^{1, 2}College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing, 210016, China
^{1, 2}National Key Laboratory of Science and Technology on Helicopter Transmission, Nanjing University of Aeronautics and Astronautics, Nanjing, 210016, China
^{2}Corresponding author
Vibroengineering PROCEDIA, Vol. 32, 2020, p. 111116.
https://doi.org/10.21595/vp.2020.21475
Received 16 May 2020; accepted 24 May 2020; published 29 June 2020
JVE Conferences
Considering multiple nonlinear parameters, a nonlinear dynamic model of star gearrotorbearing transmission system of GTF (Geared Turbofan Engine) gearbox is established. The dynamic responses are obtained through RungeKutta numerical integration method, and the responses with the variation of input rotational speed are analyzed and illustrated. The abundant nonlinear characteristics are presented in the results, which could be guidance to avoid undesirable nonlinear motion, and provide a reference for the design and control of the transmission system in GTF gearbox.
 The coupled bendingtorsional nonlinear dynamic model of GTF gearbox is established.
 The multiple nonlinear parameters, including gear backlash and bearing clearance are fully considered.
 The nonlinear response of the system under varying input rotational speed are obtained.
Keywords: star gearrotorbearing system, nonlinear dynamics, chaos and bifurcation.
1. Introduction
As the widely application of gearbox in wind turbine and aero industry, the nonlinear analysis for the gearbox, especially for those composed of planetary gears were studied. Zhou et al. [1] built dynamic model of the spur gearrotorbearing system with multiple nonlinear parameters, with the coupled lateraltorsional vibration considered. Tao et al. [2] developed a nonlinear model of a planetary gear system with multiple backlashes. Guo et al. [3] studied the nonlinear behavior of wedge teeth related to the bearing force of planetary gear system, and conducted the dynamic analysis of planetary gears considering bearing clearances [4], then studied the maximum load of planetary gears in the wind turbine drive system [5], and studies nonlinear behavior of planetary gear system in wind turbine under gravitational effects [6]. Kim et al. [7] proposed a new dynamics model for a gear set, which takes into account the torsional motion with timevarying meshing parameters. Bahk and Parker [8] conducted a dynamic analysis of the planetary gears, the resulting nonlinear behavior showed jumping phenomenon and subharmonic vibration at resonance. Li et al. [9] analyzed the nonlinear phenomena of the multistage planetary gear system. Zhao and Ji [10] proposed a nonlinear torsional model of gearbox in wind turbine multistage of planetary gear. Xiang et al. [11, 12] studied the nonlinear dynamics of multistage gears, which considered the multiclearance of the system. Hou et al. [13] established a pure rotational model of the planetary gearrotor system of the geared turbofan engine, and conducted a nonlinear dynamic analysis to obtain the torsional vibration response between the gear and the rotor. Wang et al. [14] proposed a dynamic model of GTF gearbox with elastic support of planet carrier, then [15] established nonlinear torsional model of GTF transmission system, and obtained nonlinear characteristics under excitation of important parameters.
In this paper, a coupled lateraltorsional nonlinear dynamic model of GTF gearbox is proposed, the influence of input rotational speed on the vibration response of the system is explored and quantified, then the nonlinear behavior is studied by analyzing the states of motion, mechanisms of bifurcation, and roads to chaos.
2. Dynamic model of GTF gearbox
Fig. 1(a) and (b) show the physical structure and schematic diagram of star gearrotorbearing transmission system of GTF gearbox, which is composed of star gearing system, input shaft (the rotor between lowpressure compressor and sun gear), output shaft (the rotor that connects ring gear and fan), and bearings that support input and output rotor. The star gearing system is composed of sun gear, star gear, ring gear, and planet carrier, among which, the star gears are supported by bearings, and meshed with sun gear and ring gear, both of which are semifloating components that splined with input and output shaft, respectively.
Fig. 1. Structure of GTF gearbox
a) Physical model
b) Schematic diagram
2.1. Dynamic model of star gearing system
The globe coordinate system $OXY$ is established, base on the fixedaxis rotation of the gear components in the system. Fig. 2(a) and (b) show the model of the system, respectively. Three DOFs were considered for each components, including translational displacements and torsional displacements. The main gear components in the star gearing system were represented by the subscripts $s$, $p$, $r$.
Fig. 2. Modelling of star gearing system in GTF gearbox
a) Physical model
b) Dynamic model
In which, ${k}_{sp}$, ${c}_{sp}$, ${k}_{rp}$, ${c}_{rp}$ indicate the meshing stiffness, and damping of external and internal meshing pairs, the value of stiffness are calculated by the formulas [16]. Then the meshing forces can be calculated by the following equations:
where $f({X}_{sp},{b}_{sp})$, $f({X}_{rp},{b}_{rp})$ is the nonlinear function of backlash.
2.2. Mathematical model of GTF gearbox
The system has a total of $5N+12$ DOFs, where $N$ is the number of star gears, then the overall arrays of displacement can be expressed as:
$i=\mathrm{1,2},...N.$
The dynamic equations of the transmission system in GTF gearbox can be derived as follows:
where ${m}_{i}$ is the equivalent mass in rotational direction, ${M}_{i}$ is the mass of components, $U$ is rotational displacement around $Z$ direction, $H$ and $V$ are translational displacement in $X$ and $Y$ direction. ${T}_{i}$ represents the input or output torque, ${c}_{i}$ represents torsional damping or support stiffness, ${k}_{i}$ represents torsional stiffness or support stiffness.
In order to eliminate the rigid body displacement, the following dimensionless variables are introduced for rotational displacement of each member. The dimensionless time parameter $\tau $ can be expressed by:
where, ${I}_{i}$ is the moment of inertia, ${R}_{bi}$ is the radius of base circle.
Then the derived dimensionless parameters can be defined as:
where, ${b}_{c}$ is the dimensionless parameter of displacement.
3. Results and discussion
The basic parameters used for calculation of the nonlinear vibration response of the GTF transmission system are shown in Table 1.
Table 1. Parameters of the GTF transmission system
Parameters

Value

Unit


Sun gear

Star gear

Ring gear


Number of teeth

43

42

127

–

Helical tooth width

60

mm


Normal modulus

3.5

mm


Normal pressure angle

22.5

degree


Helical angle

27

degree


Damping ratio of meshing stiffness

0.02

–


Comprehensive meshing error

15

μm


Half gear backlash

10

μm


–

Star bearing

–


Bearing stiffness

1.3e8

N/m


Bearing damping

1.2e4

Ns/m


Bearing clearance

5

μm

The vibration response of the system were conducted as the variation of input rotational speed, while other parameters are being constant. The bifurcation diagram of lateral displacement of star gear is shown in Fig. 3. Here, the input rotational speed (r/min) is control parameter, which varied between $n\in $ [8000, 18000]. As the input rotational speed increases, the system experiences periodic motion, quasiperiodic motion, and chaotic motion, successively, finally the system turns back to periodic motion through inverse bifurcation by perioddoubling scenario. The nTperiodic motion is illustrated when $n<$9000, for lateral displacement of star gear, as the input rotational speed increases from $n=$9000 to $n=$10000, the peiodic motion is turned into quasiperiodic motion, while the speed further increases, the chaotic motion is indicated in the system through quasiperiodicity until the speed arrives at 11500 rpm. As the further increasing of input rotational speed, the system turns back to nTperiodic motion while the input rotational speed varying from $n=$11500 to $n=$11900, finally the system performs periodic motion as $n>$11900.
The vibration response of the gear system in the lateral displacement of star gear were analyzed at three input rotational speeds of $n=$81000, $n=$9300, and $n=$10800, the results are shown in Fig. 4, from which different dynamic characteristics in various speed can be observed. When the control parameter $n=$8100, the system response is dominated by the meshing frequency ${f}_{m}$, the amplitude of which is much bigger than the response of other orders of meshing frequency, besides the meshing frequencies, the variable bearing stiffness frequency ${2f}_{b}$ appears. The Poincare map that obtained shows a cluster of concentrated points when $n=$8100, while several coincident circles are illustrated in the corresponding phase diagram, therefore, the nTperiodic motion is indicated for the system. As the control parameter $n=$9300, although meshing frequency ${f}_{m}$ is still the dominant response, the multiplication frequency components of variable bearing stiffness frequencies as ${f}_{b}$, ${2f}_{b}$, ${5f}_{b}$, ${9f}_{b}$ can be observed. The Poincare map turns to be a phaselocked loop, and a trajectory torus is presented in phase diagram. The characteristic demonstrate that the gear system turned into quasiperiodic motion. As the control parameter arrives at $n=$10800, a disordered set is shown in the Poincare map, and the corresponding phase diagram becomes a chaotic attractor with a random crew, thus, the chaotic motion is indicated for the system. In this situation, the meshing frequency is no longer the dominant response, which is replaced by the bearing stiffness frequencies ${f}_{b}$ and ${5f}_{b}$, then the multiplication of bearing frequency components ${2f}_{b}$, $10{f}_{b}$ also appears with more obvious amplitudes.
Fig. 3. Bifurcation diagram of system with varying input rotational speed
Fig. 4. Vibration response of sun gear and star gear meshing pair: a) $n=$8100, b) $n=$9300, c) $n=$10800
a1) Time history
a2) Phase plane
a3) Poincaré map
a4) FFT spectrum
b1) Time history
b2) Phase plane
b3) Poincaré map
b4) FFT spectrum
c1) Time history
c2) Phase plane
c3) Poincaré map
c4) FFT spectrum
4. Conclusions
In this paper, the dynamic model of the transmission system in GTF gearbox is established, based on which the coupled bendingtorsional nonlinear dynamic analysis was conducted, then the inﬂuences of input rotational speed on the nonlinear dynamic response were studied. As the input rotational speed increases, nTperiodic motion, quasiperiodic motion and chaotic motion are indicated successively, however, the system finally turns into nTperiodic motion through inverse bifurcation. The nonlinear dynamic characteristics such as appearance of combination frequency components and continuous frequency components due to the increase of input rotational speed, therefore, the system should be well controlled under certain range of input rotational speed in order to avoid the chaotic motion.
Acknowledgements
The authors are grateful for the financial support provided by the National Natural Science Foundation of China under No. 51775265. In addition, the authors declare that there is no conflict of interests regarding the publication of this article.
References
 Zhou Shihua, et al. Nonlinear dynamic response analysis on gearrotorbearing transmission system. Journal of Vibration and Control, Vol. 24, Issue 9, 2018, p. 16321651. [Publisher]
 Tao S., Yan H. Nonlinear dynamics of a planetary gear system with multiple clearances. Mechanism and Machine Theory, Vol. 38, 2003, p. 13711390. [Publisher]
 Yi Guo, ParkerRobert G. Dynamic modeling and analysis of a spur planetary gear involving tooth wedging and bearing clearance nonlinearity. European Journal of MechanicsA/Solids, Vol. 29, Issue 6, 2010, p. 10221033. [Publisher]
 Guo Y., Parker R. G. Dynamic analysis of planetary gears with bearing clearance. Journal of Computational and Nonlinear Dynamic, Vol. 7, Issue 4, 2012, p. 041002. [Search CrossRef]
 Guo Y., Keller J., Cava La W. Combine effects of gravity, bending moment, bearing clearance, and input torque on wind turbine planetary gear load sharing. American Gear Manufacturers Association Fall Technical Meeting, Dearborn, Michigan, 2012. [Search CrossRef]
 Guo Y., Jonathan K., Parker R. G. Nonlinear dynamics and stability of wind turbine planetary gear sets under gravity effects. European Journal of Mechanics A/Solids, Vol. 47, 2014, p. 4557. [Publisher]
 Kim Woohyung, Hong Hee Yoo, Jintai Chung Dynamic analysis for a pair of spur gears with translational motion due to bearing deformation. Journal of Sound and Vibration, Vol. 329, Issue 21, 2010, p. 44094421. [Publisher]
 Bahk CheonJae, Parker Robert G. Analytical solution for the nonlinear dynamics of planetary gears. Journal of Computational and Nonlinear Dynamics, Vol. 6, Issue 2, 2011, p. 021007. [Publisher]
 Li S., Wu Q. M., Zhang Z. Q. Bifurcation and chaos analysis of multistage planetary gear train. Nonlinear Dynamics, Vol. 75, 2014, p. 217233. [Publisher]
 Zhao M. M., Ji J. C. Nonlinear torsional vibrations of a wind turbine gearbox. Applied Mathematical Modelling, Vol. 39, 2015, p. 49284950. [Publisher]
 Ling Xiang, Gao Nan, HuAijun Dynamic analysis of a planetary gear system with multiple nonlinear parameters. Journal of Computational and Applied Mathematics, Vol. 327, 2018, p. 325340. [Publisher]
 Xiang Ling, et al. Nonlinear dynamics of a multistage gear transmission system with multiclearance. International Journal of Bifurcation and Chaos, Vol. 28, Issue 3, 2018, p. 18500340. [Publisher]
 Hou Lanlan, Cao Shuqian Nonlinear dynamic analysis on planetary gearsrotor system in geared turbofan engines. International Journal of Bifurcation and Chaos, Vol. 29, Issue 6, 2019, p. 1950076. [Publisher]
 Wang Siyu, Zhu Rupeng Study on load sharing behavior of coupling gearrotorbearing system of GTF aeroengine based on multisupport of rotors. Mechanism and Machine Theory, Vol. 147, 2020, p. 103764. [Publisher]
 Wang Siyu, Zhu Rupeng Nonlinear torsional dynamics of star gearing transmission system of GTF gearbox. Shock and Vibration, Vol. 2020, 2020, p. 6206418. [Publisher]
 Maatar M., Velex P. An analytical expression for the timevarying contact length in perfect cylindrical gears some possible applications in gear dynamics Journal of Mechanical Design, Vol. 118, Issue 12, 1996, p. 586589. [Publisher]
Cited By
Mechanical Systems and Signal Processing
Siyu Wang, Rupeng Zhu

2021

Mechanism and Machine Theory
Siyu Wang, Rupeng Zhu

2021
